My air rammer has a rubber knob from a rubber hammer, I have aluminium flasks and steel would ruin them real quick I would think
My air rammer
My air rammer
When life gets tough, remember: You were the strongest sperm
Re: My air rammer
just saw this post, nice how big was the hammer and did you have to drill the hole in the rubber, I just have steel plate on mine which I should use more, how much air you run on it I run about 40 psi on mine?
I need to glue up some boards and turn me another hand rammer as mine is on the short side and I got the hand grip part to large for it to be comfortable.
I need to glue up some boards and turn me another hand rammer as mine is on the short side and I got the hand grip part to large for it to be comfortable.
David and Charlie aka the shop monster
If life seems normal your not going fast enough" Mario Andrette
If life seems normal your not going fast enough" Mario Andrette
Re: My air rammer
I'm thinking about making one based roughly on this one.
Re: My air rammer
I saw that video the saw doesn't have much power I wouldn't think that it would ram sand up very tight, but thats just my feeble old brain thinking again
David and Charlie aka the shop monster
If life seems normal your not going fast enough" Mario Andrette
If life seems normal your not going fast enough" Mario Andrette
Re: My air rammer
I can understand why might think so. I'll leave a comment on youtube, ask the guy if he's happy with the results, let's see what he says.
Re: My air rammer
I don't remember the hammer size Dave but the rubber peice is 1 3/4 long the dia at the face is 1 15/16 and the hole is 1 1/16 dia, no I didn't drill the hole, every thing was made to fit the rubber. not to sure on the psi, when ever I'm using it I run two 8 cfm compresses and open them right updallen wrote:just saw this post, nice how big was the hammer and did you have to drill the hole in the rubber, I just have steel plate on mine which I should use more, how much air you run on it I run about 40 psi on mine?
I need to glue up some boards and turn me another hand rammer as mine is on the short side and I got the hand grip part to large for it to be comfortable.
Mike
When life gets tough, remember: You were the strongest sperm
Re: My air rammer
it would be nice to know how his turned out I watched the video, but don't have the ability to weld aluminum which is how he secured the stem to the foot, its threaded onto the shaft that actuates the saw blade.Rocco wrote:I can understand why might think so. I'll leave a comment on youtube, ask the guy if he's happy with the results, let's see what he says.
Mike I've used mine a couple times, I turn the air down on it to about 40 pounds which seems to work pretty good for it having a steel foot on it. I took one of the Chisels and cut the end off of it and welded on a half inch long piece of two inch round bar this seems to work pretty good in the ramming department, just have to watch out that you don't get it up on the flask or pattern.
DAllen
David and Charlie aka the shop monster
If life seems normal your not going fast enough" Mario Andrette
If life seems normal your not going fast enough" Mario Andrette
Re: My air rammer
dallen wrote:
just have to watch out that you don't get it up on the flask or pattern.
DAllen
That's the reason why I have the rubber on it, I brought some professional snap flasks off ebay last year and I sure don't want a steel air hammer any were near the flasks
Mike
When life gets tough, remember: You were the strongest sperm
Re: My air rammer
I was thinking making that part as a one piece casting rather than a weldment.dallen wrote: it would be nice to know how his turned out I watched the video, but don't have the ability to weld aluminum which is how he secured the stem to the foot, its threaded onto the shaft that actuates the saw blade.
DAllen
Re: My air rammer
that would work also, you would just have to drill the hole in the end and thread it as the guy in the video did, only free hand unless you have a pretty big lathe so that the foot would fit in the spindle.
David and Charlie aka the shop monster
If life seems normal your not going fast enough" Mario Andrette
If life seems normal your not going fast enough" Mario Andrette