My Hand Planes

User avatar
Jammer
Posts: 1620
Joined: Thu Jun 02, 2011 4:04 pm
Location: Ohio

Re: My Hand Planes

Post by Jammer »

He had the shaper in his back yard and ran it with a lawnmower engine. 8-) :P He had a lot of stuff, I hope someone got it that could use it. sometimes the family just scraps everything because they don't want to deal with it.
8-) 8-)
cae2100
Posts: 434
Joined: Fri Dec 22, 2017 5:39 pm
Location: Middle of Nowhere, Ohio

Re: My Hand Planes

Post by cae2100 »

well, I made a bit of progress on the checkering planes... I machined up the bottoms of them and the steel was really wierd, full of hard spots, and hard to work with properly. I had to machine it a few times because I kept screwing it up, and when I took it out of the vise, I realized that it was way too thin and the plane itself had moved in the vise and shifted somehow, which made one side thicker than theh other, throwing everything off, and ruining the whole plane. I realized after that that the planes were far too thin for the soles and I really didnt like it at all, so I took it back out to the forge and heated them back up and that melted the braze. I lifted the top up and the top/body and soles just fell off, and I brazed on a new bottom/sole that is much thicker, and is mild steel that should be much easier to machine up.
20260831_194914.jpg
They're in the vinegar picklling tub right now, dissolving all of the scale off of them again, and getting them ready to redo the machining all over again. I wasnt 100% happy with them before, but I like them more now with that front toe on it, which I didnt have enough material to add to them last time. It also gives me something to grip onto to machine the insides also.

I also had another plane body forged out a while back, that never got converted to square ended box tubing, so I just stuck a piece of steel on it also while I was brazing up the other planes, lol. I have no idea what to do with it yet, but I'd probably just stick it in my pocket and use it wherever really I think as a block plane, lol. Ive been looking at ideas of different types of planes, but there isnt anything that I can find that I really need that I could use that one for, lol. I did think of using it as a toothing plane, but Ill have to see how the checkering planes work, since it'll be pretty much the same thing, but with a much lower blade angle, and a smooth bottom instead of a V grooved bottom.

So not much to report on that progress, went to step 7 or 8, and got put back to step 4 or 5, lol. Now just waiting on the scale to dissolve off of them so I can machine them up without the scale throwing stuff out of precision, or tearing up my cutters.
cae2100
Posts: 434
Joined: Fri Dec 22, 2017 5:39 pm
Location: Middle of Nowhere, Ohio

Re: My Hand Planes

Post by cae2100 »

Well, life went a bit crazy and I havnt able to work on those planes in a while. I had an idea of a checkering float that I made up a 20 lines per inch, everything went ok, but unfortunately, it doesnt want to work like the 16 lines per inch one. I think it might have to do with cutting angles, grooves, or something, but Ill play with it here and there till I can hopefully figure it out. The cold has been my enemy for a few months now due to this bug, so Ive been unable to go out, and unable to sit there for long periods of time to work on it in the cold shop.

In the mean time, I got onto a kick of one of the oldest types of hand planes, kinda, which is called a scratch stock. Ive made a few over the years and they did kinda work, but they always jammed up on me. Even the commercial ones jam up also, so I had an idea for one a while back and thought that it would be really awesome to have a scratch stock, but in the same design as my quirk router that I absolutely love. This tool here:
20240911_124313.jpg
I sat down with my quirk router and looked at it for a while and started doodling up a different design, and got a pretty nice shape that I was happy with. After getting it mostly doodled up and transfered to the piece of wood, I realized that the same company made the quirk router also made the exact tool I was making, but it looked so thin that it looked like it'd break at any moment, so I wasnt too impressed with it unfortunately. I then took the block of wood out to the garage, drilled some holes in it, cut it out, and brought it back in so I can work on it in the basement where it was warmer at, and went to town on it using with the whittling knife to shape it, lol.
20261101_024236.jpg
20261101_024213.jpg
After shaping the back a bit more with the whittling knife to round it over and then taking a file and scrapers to it to clean up the facets and file marks, it was flipped over and stuck in a wooden hand clamp, and finger grooves were cut in it with my spoon gouges. I then cut two grooves parallel to the sides with a hand saw and cut with V carving chisel to get a good place for the small radius plane to register into and follow. It was then taken to depth with the small plane, that way the fence could have the two matching 3/16" diameter half rounds on it to register on it, and it wont interfere with the cutter/blades like the setup with the quirk router's fences would.
20261102_025927.jpg
20261102_025942.jpg
20261102_030152.jpg
Somehow or another, the stupid grooves that I did up, the small U groove plane didnt follow the one for some reason and it messed it up, so I filled it in with wax and tried fixing it with my other scratch stock, which the fence was not long enough to do the job, so I grabbed a piece of cherry that was sitting at my feet at the time and just took it out to the table saw and bandsaw real quick and cut it out to make up a scratch stock plane to fix the U grooves, so they were running perfectly parallel.
20261105_063354.jpg
20261105_063440.jpg
20261105_063545.jpg
After fixing the grooves, I grabbed two pieces of cherry that I had sitting here an laid them out to make a pair of fences for the plane, and took them out, and repeated the whole drilling and cutting it out with the bandsaw routine to rough them out, lol. I made one into a radiused surface, and the other was flat/square. I just sat here the one day and used my chisels to shape the fences and get them just perfect how I wanted them, then added wax fillets and everything to the main plane pattern and the fences.

The half rounds for the fences were an interesting excercise because of how thin they are, so I took the same half round groove hand plane I used previously and did some grooves in a spare piece of cherry that was smooth and flat, and then drilled into the grooves with a 1/4" bit. I then took the scratch stock blade that I used to fix the grooves earlier to get them perfectly parallel, and used that to scratch the U grooves slightly deeper. When I took a 1/4" dowel and hammered it into those holes, it acted as a stop and I could plane down the 3/16" dowels till the plane hit the board, then I knew I was done. That made the half rounds so when they are put together into the main plane body, it sticks above slightly under 1/32", so plenty of material to have them register in the grooves once it's cast, but tight enough tollerances that I wont have to worry about needing to machine anything. Those half rounds were glued onto the fences and everything was coated in a few coats of shellac.
20261105_063709.jpg
20261111_162129.jpg
20261111_161811.jpg
You can see here how they fit into the grooves on the bottom of the plane, then when they're cast in bronze, they'll get a slot milled in the middle of them, and they'll be good to go from then on.
20261111_162040.jpg
I have some bandsaw blade from a sawmill, which is 1/16" thick, and I'll cut that up and grind off the teeth to make up some cutters for this plane once it's cast. Ill also be able to use bed frame, or whatever steel I want because it'll have an actual mouth on it and probably be held in with a homemade carriage bolt like my quirk router was.

With conventional scratch stocks, they have no mouth and when it starts to get close to the body of the tool, or down to depth, it wants to jam up alot, so with this one, it'll have an actual mouth and should never jam up on me. It should allow me to put profiles in to clean up coreboxes, glue up square cutoffs on a pattern and use it to round over those into a nice bead or whatever I want, and it'll act like a hand plane with whatever profile I want, but with the benefit of having a fence on it too, so lots of accuracy. I thought about making one more fence, but with a massively long fence on it, but Im not entirely sure I'd ever really use it when I have the other plane body above that I can just stick the stuff in if it's close to the side.

In case you arent sure what a scratch stock is, think of a tool that you can stick a piece of steel in that's filed to the profile you want, or really the mirror opposite of it, then you just drag it back and forth on the workpiece to scrape that profile into the wood. You would normally rough out the bulk of it with a block plane or whatever, then you can go over it with that till the scratch stock bottoms out, and you'll have not only the exact perfect profile you wanted, but it's smooth to the point that it doesnt even need sanding afterwards. It's not as fast as a hand plane at doing the profile, but it is pretty quick on it's own tbh. If youre trying to replicate really old antique molding or something, you would usually use that since you can copy it and you dont need custom planes or custom router bits, just shape a piece of old hand saw, or whatever piece of steel and it gets dragged through the wood till it is at depth and the profile you wanted. There are a bunch of different designs out there, but for me, pretty much all of them all have issues with no mouth on them, and they tend to jam up in use. So you have to keep stopping and clean out the cutter every pass or multiple times per pass.

Thats about all that Ive been working on here, just trying to get healed up and trying to avoid the cold in fear of making things worse, lol. I had a forging job that came in that I was trying to get done up when it was warmer out, so you can see those in the pics with the fences and such. He wanted some custom chisels like japanese chisels, but with flat backs and made a little different, so I just made them how he wanted them, lol. We've also been canning alot of food and getting things set back for winter and the upcoming year.
cae2100
Posts: 434
Joined: Fri Dec 22, 2017 5:39 pm
Location: Middle of Nowhere, Ohio

Re: My Hand Planes

Post by cae2100 »

In my down time, I was looking at toothing planes, and they're virtually the same thing as my checkering planes, except that the holes are just flat rather than grooved, and the blades are grooved also like the checkering planes. Man has that been a research rabbit hole, lol. Trying to find actual answers has been difficult since most were just cut with a chisel like a file was, and the amount of teeth per inch was just whatever the person making it felt like at the time, lol. Later ones were machined and had V grooves like Im planning on doing on the checkering planes, and the newest ones today, they're used for completely different purposes, so the teeth are just square grooves cut in the blade, so it just cuts really thin strips of wood rather than a wide surface. The newest toothing plane blades are made for dealing with really rough grain, like burls and stuff like that to get it flat, then you would just scrape off the high spots afterwards with a card scraper. The V groove ones were used for veneer work, which is what I was wanting it for, and the teeth per inch varied pretty widely to say the least, lol.

After what feels like way too much research, I saw that stanley did release a set of 3 toothing blades that had 26, 28, and 32 teeth per inch, which the 28 was the best for veneer, and 32 was more for really fine marquetry.

I was wanting it for veneer work because I had the idea to take thin pieces of wood, like 1/8" thick and putting a texture on it, then when I want checkering or a texture on a pattern, I can just glue a veneer on it and I'd be done with it, lol. With hide glue, it works great indoors, but with thin veneers, in damp and places that change humidity levels, like the sand molding bench, the thin boards can let the moisture through it quickly enough that it might start reacting with the pattern and start wanting to come loose. So I just decided to tooth the pieces and not have to worry about taking the chance, lol.

With modern glues, that's not an issue and the toothing can be a bad thing, but with the old hide glue, it also tears up the wood fibers and lets the glue soak into the wood itself rather than sitting on top of it, so it ends up with a much much stronger grip.

I was thinking of doing some stippled veneers, checkered, and some other ones that Ive seen textured on old patterns, so I figured it'd be pretty easy and speed things up for me. It also allows me to have inside pockets on patterns that are checkered, without having to do it right then and there on the pattern and risk something going wrong and ending up with checkering that has some issue. I can just do up a large bit of thin boards and cut out a good spot and glue it on and be done with it.

So I was able to get some bed frame flattened out and I cut it into two blade blanks that Ill use in my patternmaker's plane, just removing the sole and taking advantage of the large mouth, to use it as a toothing plane to tooth the surfaces. I just havnt gotten out to the shop to machine them up yet, but Ill probably make it up as 28 teeth per inch in the end, which seems to be the best option imo. Ill set the stroke length on the shaper up really short, and use the shaper to cut the teeth in it, which wont take long at all tbh. I have no idea what I'd use the other blade for I made, but it'll be for something I guess, lol. Ill probably just keep it as an extra blank to shape it however I wanted.

Lots of lounging around doing not much but looking stuff up, and not doing it, it seems, lol. Ive been selling a few of my hand planes over the last few months, and have 3 to ship out right now to the same guy in florida as the chisels and tools are going to. The only ones in that batch I really wanted was the convex sole plane, which Ive used a whole one time in all the time Ive had it, and it's just taken up room in the one drawer. So it's out of here and I know the guy will use the thing quite alot for shaping chair seat butt prints. The other one is the compass plane, which has never been used, and Ive been looking at homemade ones that are much more of what I was looking for also. I sold a few others to the one guy a month ago, and made a decent amount off of the one little pipe plane that he wanted for himself, and the other he was selling for me, so we'll see how long it'll take before that sells. It was a very old and very rare and fairly collectable plane, so it may take a while to sell, or it might have sold already, lol.

Other than that, not much new, just tinkering with this and that really, lol.
Rasper
Posts: 656
Joined: Sun Aug 07, 2011 4:05 pm
Location: Huatulco, Oaxaca, Mexico
Contact:

Re: My Hand Planes

Post by Rasper »

A note here to let you know you have an appreciative audience. Keep up the posting.

Richard
cae2100
Posts: 434
Joined: Fri Dec 22, 2017 5:39 pm
Location: Middle of Nowhere, Ohio

Re: My Hand Planes

Post by cae2100 »

Thank you richard, I really do appreciate it.

Side note, I did finish the spill planes and the one went to the mccook house at algonquin mill festival. I had a blacksmithing buddy come out before algonquin and he was working on forging some stuff out, and I sat there with my patternmaker's plane and made up the wedge for it while he was working on his stuff. I sharpened it up and that thing worked great, so I made a bunch just testing it and setting it up, then took bundles of 15 spills and wrapped them up with ones that werent nicely shaped, just unrolling it and putting it around the bundles of spills as it's own banding. I did that up for a bunch of bundles and put it all in the box with the plane and took it over to algonquin with me, and talked to the guy in charge of the historical society and he about jumpped out of his boots when I said what I had, lol. He knew what the spills were, but had never seen them nor known anywhere to get them.

The mccook house over at algonquin was an early 1800s stage coach stop and kinda a hotel, and when they got the place, it was taken back to period exact, so the spills were right at home in there, lol. What the wooden spills are, back before matches were invented, you would always have a fire going in your fireplace or a fire going in your cookstove, and you would just light one of these wooden spills off of the hot coals, and you can walk around your house to light your candles, lantern, tobacco pipe, or whatever you need to light. They light pretty easily, and they burn very very slowly, about as slow if not slower than a match does. I got tired of our long neck clicker lighters not having gas in them, so I made the spills up so I can light the candles down inside the glass jars when they burn down a little bit, and you cant reach them with a normal lighter or matches, lol. I just finished up the second one I was working on earlier today when I sharpened the blade, but finished it off about 2 weeks ago when I finished shaping the wedge for it.

This is the one that went to algonquin along with a bunch of cherry spills, which mine looks identical except a bit more minieral staining in the wood is all.
20261007_114454.jpg
20261007_114526.jpg
User avatar
Jammer
Posts: 1620
Joined: Thu Jun 02, 2011 4:04 pm
Location: Ohio

Re: My Hand Planes

Post by Jammer »

Those all look fantastic as usual. Great that you're able to get some stuff done. It's supposed to warm up this week, are you going to try to cast those?
8-) 8-)
cae2100
Posts: 434
Joined: Fri Dec 22, 2017 5:39 pm
Location: Middle of Nowhere, Ohio

Re: My Hand Planes

Post by cae2100 »

I didnt even look at the weather for this week, but now that you mention it, it does look pretty nice, lol. Ill have to find something else to throw in the one mold to take up some room since it's a fairly large flask for just the fences, which are pretty small. I went out last night to ram up the molds, but had to wait for the air compressor to pump up and it was giving me some trouble, then the misquitoes came out in full swarm in the shed, so I knew I was done for the night, lol. I measured out that I needed around 1 1/2lbs for everything, and went to the shop with some magnets and found that most of the bronze I had in the drawer fom old risers/sprues and such were all al-bronze, so I put them all together and have almost 4 1/2lbs, so that'll work to pour it in. I was wanting to pour them in al-bronze anyhow, and now I dont have to fart around with alloying it right at this moment, lol.

Ill ram them up today, then pour them either today or tomorrow. I have a bunch of stuff I want to forge out anyhow before the weather crashes out anyways, so Ill do that up through the rest of the week. I figured I'd get up early and ram them up, but just looked and it is around 25F on the thermometer outside, so Im not in any rush to go out there to ram them up, lol. I already took the patterns out to the molding bench and put them in the flasks, which I have a large shallow one that I used for the pantograph casting, so that should be good enough for the main pattern. We'll see how it goes later today if I can do it or not.
cae2100
Posts: 434
Joined: Fri Dec 22, 2017 5:39 pm
Location: Middle of Nowhere, Ohio

Re: My Hand Planes

Post by cae2100 »

All cast in aluminum bronze and it came out pretty good.
20261118_203359.jpg
20261118_203442.jpg
20261118_203806.jpg
20261118_204245.jpg
The surface finish on the main body is extremely good, to the point that it's almost hard to tell that it was cast because it's so smooth and no sand texture on it since I had the gating choked so hard. The very end of the flat part didnt fill all the way to the tip, but most of them I saw had that machined back anyhow and never understood why, Now that it's like that, I really do understand because the grip is far more comfortable than it was on the pattern, and it adds clearance for the fence too, so Im not worried about recasting it tbh. If you look up a preston 1393 reeder plane, you can see what I mean.

All that needs to be done on it is drill and tap a few holes, and cut a slot in the fences. Other than that, those things are done and ready to make cutters for. I plan on using bandsaw blade for my cutters, but I can also use stuff like spring steel banding, hand saw blade pieces, and even bed frame for the cutters. You just grind or shape them with files, clamp it in the tool using the clamping bolt, and it'll cut the reverse of that profile in your wood. It's honestly about as fast as a hand plane, but much much more versatile. Ive been wanting a good scratch stock for a while, that wont jam up on me in use, and I think this should be perfect in every way for what I was after.
User avatar
Jammer
Posts: 1620
Joined: Thu Jun 02, 2011 4:04 pm
Location: Ohio

Re: My Hand Planes

Post by Jammer »

Wow! those came out great. I'm so jealous. :D 8-) 8-)
8-) 8-)
Post Reply

Return to “Corner for the Creative”